Power Burners
Our Power Burners are forced air burners that have several advantages over Venturi burners. Since air and gas are independently controlled, then mixed, these burners are very efficient. The high volume, long flame length helps produce quicker, more efficient firings. Power burners, with their forced air, do not depend upon the chimney to provide draft. Chimneys need only be tall enough to remove the flue gases from the kiln shed or building. Working on low pressure, Power Burners can be used with either propane or natural gas. These burners are designed to deliver high output on low pressures (14"WC or less). The Btu figures at right are based on natural gas delivery @ 7"WC with .65 specific gravity and propane delivery @ 11"WC with 1.522 specific gravity. Orifices can be adjusted to deal with a wide range of low pressures.A brass gas cock (1), provides 100% shutoff. Air is controlled by the variable speed control (2) and the manual air shutter (4) and provided by the continuous duty blower (5). A sediment trap (3) prevents sediment from passing through the gas train. The BASO™ valve (12) is connected to the pilot burner (6) which can be adjusted by the CSA/UL approved gas cock (10). The pilot energizes the thermocouple (7) and ignites the main flame which is held constant by the flame retention nozzle (8). An CSA/UL approved ball valve provides smooth gas flow adjustment (9). An optional electric solenoid valve (11) provides instant shutoff in the event of power failure. Electrical connection is by a grounded 6' cord (13).Please refer to our Burner Ordering Info page before selecting or ordering burners.
The Btu values in the table above are examples only. All Power Burner orifices are drilled for your specific Btu requirements.
The equipment listed below is optional. The prices below are the installed prices in addition to the burner base price listed above. For your burner price, add the base price (above) plus any optional equipment..
The equipment listed below is optional. The prices below are the installed prices in addition to the burner base price listed above. For your burner price, add the base price (above) plus any optional equipment..
Optional Equipment
Electric Solenoid Valve. This valve provides instant shutoff in the event of power failure. Flame may lick up the outside of the kiln or go back into the blower during a power outage if this valve is not present. Mounted downstream of BASO; shuts down main burner but leaves pilot burning for automatic reignition upon re-establishment of electricity. Mounted upstream of BASO; shuts down both main and pilot burners with loss of current, calling for manual re-lighting. NOTE: DO NOT operate in damp or wet areas.
Price: $209.00.
Water Column Gauge. This gauge helps produce repeatable firings by providing a reference point based on differential pressure or pressure drop depending on valve location in relation to flow control valve.
Price: $69.50
Ransome Piggyback Venturi Burner. This Venturi pilot burner is excellent for overnight warming and windy areas. Power Burners may not be able to provide the very low settings needed for the start of bisque firings. This optional pilot can provide several thousand Btu’s of heat to completely dry out the load. Comes with attaching clamp, large oval head, baffle plate, gas cock, supply line, and thermocouple fitting. 2,000 to 4,000 Btu output.
Price: $199.00
Spark Ignition. Spark ignition provides an additional level of safety and convenience. Flip a switch and the transformer produces a very intense spark at 300 pulses a minute. Upon pilot ignition, sparking stops. If there is a pilot outage, the electrode senses this in less than 1 second and reignites the pilot. Safe, Fast, Easy.
Price: $199.00
Price: $199.00
Adjustable Burner Stand. This burner stand securely holds the burner parallel to the floor and can be rotated 360° or adjusted vertically through it's range. Three height ranges measured from the center of the main burner nozzle.Short: 16" - 22" Medium: 22" - 32" Tall: 28" - 38"
Price: $199.00
90° Burner Head. Used when space is at a premium. Allows the burner to be kept close to the wall of the kiln. See below for configurations.
MB200 thru MB400 Price: $42.95 MB500 thru MB700 Price: $89.95
MB200 thru MB400 Price: $42.95 MB500 thru MB700 Price: $89.95
220 Volt Conversion. For our customers who do not use 110-120 Volts. Because of the wide variety of male/female plug types in use around the world, the power cord will come without male plug.
Price: $129.00
Needle Valve. For those that want very precise control of the main burner. These valves are rated to 400 psi WOG (water, oil, gas) and provide smooth, precise, and incremental throttleing of the main burner.
Price: $97.50
Price: $97.50
Key Gas Components Shutoff Valve. These large handled shutoff valves are internally lubricated and provide a very smooth adjustments. CSA approved with built in gauge ports.
Price: $42.95
Price: $42.95
C2
C3
C4
C5
C6
C7
NOTE: There is a $250 shipping upcharge per burner on the following configurations: C3, C5, & C7. If you do not specify a configuration for your burner(s), they will be built in the C1 style (see top of this page). To order one of the configurations above, add C and the number. Example; 2- MB200C6. NOTE: Pairs of burners are built as mirror images of each other.